---

------------------------------------------------------------------------------ This file was downloaded from ALIENS BBS ISRAEL, the BEST BBS in ISRAEL! Call now! 052-506539 24H 250Mb on-line! ------------------------------------------------------------------------------ NOTES ON THE USE OF 1.4 MB DRIVES IN AT-COMPATIBLES: I wasn't long after 1.4 Mb drives became available on the aftermarket that users discovered there are significant problems is applying then to AT's. Many of Second Nature's users have asked for help or advice, as SecNat has a feature to help in 3.5" disk installation on older AT's with no BIOS 3.5" support. All sorts of strange stories are filtering back from the people who sell such drives, some of it contradictory, so I felt it was time to get all the facts in one place. The use of 720k 3.5" drives is non-controversial, and the drive manufacturers' instructions are generally adequate. 1.4 Mb drives, however, _will_not_ and _cannot_ work "out of the box", due to a _basic_hardware_incompatibility_: a) The Western Digital AT-type controllers (1002 & 1003 WA2) _hard-wire_ the state of the /Reduced Write Current output on Pin 2 to the _data_rate_in_use_: Low for 300 kHz, High for _all_others_. 1.4 Mb drives use the 500 kHz data rate for 1.4 Mb disks, and the 250 kHz data rate for 720k media. THUS /RWC IS ALWAYS HIGH! b) The 1.4 Mb drive requires that /RWC be LOW for 720k media, and HIGH for 1.4 Mb media. Think of it being much like tape bias on a cassette deck -- if it's not matched properly to the media, full fidelity recording is _impossible_. Note that both of the above factors are _built_into_ the hardware, and CANNOT be changed by the BIOS, or software drivers! Thus 1.4 Mb drives, when simply plunked in an hooked up, CANNOT properly record on 720k media, and will normally TRASH as disk, if a write is attempted! Two solutions are known to work: 1) A switch on the drive allowing /RWC for the 1.4 Mb drive to be independent of input Pin 2's state. This may be done by installing a small toggle switch in the extra front panel space of the 3.5" to 5" adapter used for AT-mounted 1.4 Mb drives. The connection to pin 2 of the cable should be broken (on the drive side of the connector), and the switch wired so that in the "720k" position the circuitry previously connected to Pin 2 is closed to Logic Ground. The switch is then open in the other "1.4 Mb" position, and produces Low and High levels to /RWC, respectively. If 1.4 Mb BIOS support is available (if it's an option in your SETUP program), operation will be exactly like a PS/2 1.4 Mb drive, EXCEPT you must set the switch appropriately to the MEDIA IN USE. If you do not have BIOS support, you may use DRIVER.SYS to define the drive, with an entry like: PCDOS 3.3: DEVICE=DRIVER.SYS /D:1 /F:7 /S:18 /C AST MS-DOS 3.2: DEVICE=DRIVER.SYS /D:1 /F:4 /S:18 /C ^ (See your DOS Manual for the correct /F: number for 1.4 Mb) Command syntax for formatting will be as described in your DOS Manual. REMEMBER TO USE THE DRIVE LETTER ASSIGNED BY DRIVER.SYS WHEN FORMATTING, if you do not have BIOS support! 2) The drive can be internally modified to control the state of /RWC from the sensor for the extra hole in the body of a 1.4 Mb diskette. Surprisingly I know of no commercial drive that does this, but I verified it's practicality by today actually modifying an Astro brand Internal Drive Kit, supplied as type 1), above. Regrettably, modifying the Mitsubishi drive in the Astro required milling of the casting, and modification of numerous internal parts, but with some 4 hours work it was done, and does indeed perform automatically as desired. I suspect that the absence of Media Type Sensors in most 1.4 Mb drives is due to the proximity of the required sensor location to the Eject Button mechanism, usually carried over from the manufacturers' earlier 720k drive. With this type of media-sensing drive operation is exactly as in a PS/2, in that the only operator decision to be made is matching the Formatting commands to the actual type of media in use. There is an added advantage in that you can't "wipe out" the media, by writing to, or formatting, a 720k diskette with /RWC High -- a mistake that usually requires a powerful bulk eraser to repair, and causes the loss of any data already on the disk. Anyone wishing to supply a drive of this type may contact me for full particulars of the Media Sensor to /RWC interconnection. I'll note in closing that the Astro unit (advertised in InfoWorld) is supplied with software said to work with any DOS 2.0 and above, at $295, however if you have BIOS support you may use PCDOS 3.3 (or AST MS-DOS 3.2), instead of the supplied software. They will not unbundle the drive/software package. Clyde Washburn 70305,1211

---

The views and opinions stated within this web page are those of the author or authors which wrote them and may not reflect the views and opinions of the ISP or account user which hosts the web page. The opinions may or may not be those of the Chairman of The Skeptic Tank.

Return to The Skeptic Tank's main Index page.

E-Mail Fredric L. Rice / The Skeptic Tank